Skip to main content
Plumbing Guides

How Much Does It Cost to Replace a Hot Water Cylinder? 2026 UK and London Prices

What it costs to replace a hot water cylinder in 2026: a like-for-like vented swap, unvented supply and fit, and cylinder prices by size. UK prices first, then London, with a fair quote checklist, a worked sum, the Building Regulations and competent person rules, and VAT.

The Loacally team14 min read
A white hot water cylinder with copper pipework and one tangerine valve handle on warm paper

Last updated: November 2026. Prices and rules checked on 17 November 2026. The regulations come from legislation.gov.uk, Gov.uk and Local Authority Building Control; the fitting price comes from Which?, and cylinder and unvented prices come from dated 2026 trade guides and merchant listings, because no official body publishes them. This guide is general information, not a quote.

TL;DR: A like-for-like replacement of a vented hot water system costs about £350 to £1,000 in labour and materials, excluding VAT and the tank, on Which?'s November 2025 survey [1]. A full unvented cylinder supply and fit typically costs £1,500 to £3,500 [3]. Which? says prices are likely to be at the upper end in London and the South East [1].

A hot water cylinder is the storage tank that holds the hot water for your taps, shower and bath when you have a system or regular boiler rather than a combi. When one fails or starts leaking, the first question is cost, and the honest answer depends on one thing more than any other: whether you are replacing like for like, or changing the type of system. This guide sets out what each job costs in 2026, what a fair quote should list, the rules an installer must follow, and how London prices compare.

Vented or unvented: the difference that sets the price

A vented cylinder is fed by a cold water tank, usually in the loft, and has an open pipe that lets the system expand safely. It works at low pressure, and its safety comes from that open design. Replacing one with another vented cylinder is the simplest and cheapest version of this job.

An unvented cylinder is fed directly from the mains water supply and stores hot water under pressure, so there is no tank in the loft. Because the water is pressurised, the system relies on safety devices instead of an open vent. The Building Regulations require any hot water system with a storage vessel to "incorporate precautions to... prevent the temperature of the water stored in the vessel at any time exceeding 100°C" and to ensure "that any discharge from safety devices is safely conveyed to where it is visible but will not cause a danger to persons in or about the building" [7]. That extra equipment, and the extra competence needed to fit it, is why unvented jobs cost more.

Direct or indirect is a second choice that matters less for price. An indirect cylinder is heated by the boiler through a coil inside it, usually with an electric immersion heater as backup. A direct cylinder is heated by immersion heaters alone. Your installer should confirm which one you have before quoting.

What a fair quote for a cylinder replacement should list

A fair quote for a hot water cylinder replacement separates the cylinder, the labour and the extras, so you can compare two quotes line by line. Citizens Advice says a written quote should include "a fixed total price - not a daily rate", "a breakdown of all the work to be done and the materials needed", "how long the price is valid for", "if the price includes VAT" and "when the price can go up - for example, only if you agree to extra work" [18]. For a cylinder, that breakdown should cover:

  1. The cylinder itself: make, model, capacity in litres, vented or unvented, direct or indirect.
  2. Labour: how many days, and whether the price is for a like-for-like swap or includes pipework changes.
  3. Removing and disposing of the old cylinder, and of the loft tank if you are changing to unvented.
  4. Pipework changes: new routes, larger pipes, or moving the cylinder to a different cupboard.
  5. Unvented safety equipment, if relevant: one 2026 trade guide lists the pressure reducing valve, expansion vessel and discharge pipework as separate items costing £300 to £800 together [4].
  6. Electrical work: any new circuit for an immersion heater, which is notifiable building work [10].
  7. Building control: whether the installer will self-certify the work through a competent person scheme, or whether you need to apply to the council [8].
  8. VAT: whether it is included, and at what rate.
  9. Commissioning, warranty registration and servicing: ask what the installer does on the day, and whether the cylinder's warranty depends on regular servicing.

Citizens Advice also suggests getting "written quotes from at least 3 different traders before you decide on one" [18]. If one quote is far cheaper than the others, check whether it leaves out removal, safety equipment or building control.

How much does a hot water cylinder replacement cost in 2026?

No official body publishes cylinder prices. Which? publishes the most reliable fitting figure, from a survey of its Trusted Traders, and the rest comes from dated 2026 trade guides and merchant listings. Use these figures to judge a quote, not to replace one.

JobTypical priceWhat is includedSource
Which? row "Replace a standard hot-water tank", average three-bedroom semi£350 to £1,000, 0.5 to 1 dayA like-for-like replacement of a vented system; labour and materials, tank not included, excluding VATWhich?, survey November 2025 [1]
Vented cylinder, when swapping a combi for a boiler with a hot water tank£350 to £750Extra cost in a boiler-swap context; Which? does not say whether this is supply, fitting or bothWhich? boiler guide, 17 September 2025 [2]
Unvented cylinder, when swapping a combi for a boiler with a hot water tank£900 to £1,400As aboveWhich? boiler guide, 17 September 2025 [2]
Unvented like-for-like swap, labour only£400 to £700Labour; VAT basis not statedTrade2Base, 14 June 2026 [3]
Unvented install with pipework changes, labour only£700 to £1,400Labour; VAT basis not statedTrade2Base, 14 June 2026 [3]
Unvented cylinder, full supply and fit£1,500 to £3,500Cylinder, safety components, sundries, labour and Building Regulations notificationTrade2Base, 14 June 2026 [3]
Unvented cylinder, standard, all in£1,800 to £3,500One builder's guide; method not statedBook A Builder, 13 June 2026 [4]
Unvented cylinder, high specification£3,500 to £5,000 or moreAs aboveBook A Builder, 13 June 2026 [4]
Mains accumulator, where mains flow is too low£300 to £700 extraAdded to an unvented job only if neededTrade2Base, 14 June 2026 [3]

The Which? figure is the anchor. It comes from a survey of 25 Which? Trusted Traders gathered in November 2025, and Which? describes the job as "A like-for-like replacement of a vented system in an average three-bedroom semi-detached house. Tank not included" [1]. Which? says its prices "include labour and materials but exclude VAT, unless otherwise specified" [1]. Which? does not define "hot-water tank", but it describes the job as a vented system, which is where a hot water cylinder sits.

The unvented figures are indicative. Trade2Base is a software firm's pricing guide for tradespeople, and Book A Builder is a trade directory's guide based, it says, on hands-on experience. Neither describes a survey method [3][4]. The two agree on a top end of about £3,500 for a standard unvented job, which is useful, but treat both as market context.

No dated source we found gives a price for replacing an immersion heater on its own, for converting a vented system to unvented as a separate line, or for removing a cylinder when you switch to a combi boiler. Ask for each as its own line if it applies.

How much does the cylinder itself cost?

On an unvented job the cylinder is often a large part of the bill: Trade2Base's 210 litre supply range of £650 to £950 compares with its £1,500 to £3,500 full supply and fit [3]. Brand also makes a large difference. Trade2Base gives these 2026 supply prices for unvented cylinders [3]:

Unvented cylinder sizeSupply priceSource
150 litres£500 to £750Trade2Base, 14 June 2026 [3]
210 litres£650 to £950Trade2Base, 14 June 2026 [3]
250 litres or more£850 to £1,200 or moreTrade2Base, 14 June 2026 [3]

Branded cylinders at merchants cost more than those ranges. On 17 November 2026, City Plumbing listed a Gledhill StainlessLite System Ready 210 litre unvented indirect cylinder at £1,162.80 including VAT [5], and Heat and Plumb listed a Heatrae Sadia Megaflo Eco 210 litre unvented indirect cylinder at £1,801.95 [6] (the page labels VAT only on its default 125 litre price, so check the basis). These are retail list prices on one day, not what an installer pays, but they show why two quotes for the same size of cylinder can differ by several hundred pounds.

Size the cylinder to the household, not the house. A larger cylinder costs more to buy and to heat. Ask your installer to explain the capacity they recommend for the number of people and bathrooms, and whether your mains supply can support an unvented cylinder at all.

A worked sum: replacing a 210 litre unvented cylinder

Take a like-for-like swap of a 210 litre unvented cylinder in the same cupboard, with no pipework changes, using Trade2Base's June 2026 figures [3]:

LineLowHigh
210 litre unvented cylinder, supply£650£950
Like-for-like swap, labour£400£700
Subtotal£1,050£1,650
VAT at 20%, if the installer is VAT-registered and the figures exclude VAT£210£330
Total with VAT£1,260£1,980

Trade2Base does not say whether its figures include VAT, so the VAT line shows the most you might add [3][14]. Three things push the total higher. A branded cylinder, listed at £1,162.80 including VAT at one merchant [5] and £1,801.95 at another [6], replaces the supply line; merchant prices that already include VAT should not have VAT added again. Pipework changes move labour to £700 to £1,400 [3]. Which? says London and South East prices are likely to be at the upper end [1]. Those factors are how a job that starts at £1,050 to £1,650 can reach the top of Trade2Base's £1,500 to £3,500 range for a full supply and fit [3].

What pushes London prices up

Which? says its prices "are likely to be at the upper end of the scale if you live in London or the South East" [1], and Trade2Base says "London and the South East typically carry the highest day rates" [3]. One builder's 2026 guide puts a figure on it: "In London, it is common to see a 10 to 25 percent uplift on labour" [4]. That is a single firm's estimate, not a survey, so use it as a rough guide only.

Access can also add time in London homes. A cylinder in a tight airing cupboard, an upper-floor flat with stairs to carry the new cylinder up and the old one down, or limited parking near the job may all affect the price. Ask whether a quote allows for any of these.

The rules: who can fit a hot water cylinder

The rules below are for England; Wales, Scotland and Northern Ireland have their own building regulations, so check locally if you live there.

Hot water storage is controlled by the Building Regulations. Local Authority Building Control (LABC) says "all hot water storage devices - regardless of the volume of water stored - are controlled by the Building Regulations" [8]. Requirement G3 sets out what any hot water system must do: it "must be designed, constructed and installed so as to resist the effects of temperature and pressure that may occur either in normal use or in the event of such malfunctions as may reasonably be anticipated, and must be adequately supported" [7].

A cylinder holding more than 15 litres is notifiable. LABC says a hot water storage unit holding more than 15 litres is both controlled and notifiable. Only units of 15 litres or less with an exempt electrical supply, such as a three-pin plug socket, fall outside notification [8]. Notifiable work is handled either by a Building Notice or full plans application to the council, or by an installer who self-certifies the work through registration with an appropriate competent person scheme [8].

Competent person schemes have a technical competence for unvented systems. Gov.uk lists the schemes authorised for "Heating or hot water system, or its associated control" work, including APHC, BESCA, Blue Flame Certification, Gas Safe Register, Certsure, HETAS, NAPIT and OFTEC, and its minimum technical competences include a separate annex for "unvented hot water storage systems" [9]. In plain terms: for an unvented cylinder, ask the installer which scheme they are registered with for unvented work, and check their registration before they start. If they are not registered, ask who will notify building control, because the work still has to comply.

Electrical work has its own rule. The Planning Portal lists "a new circuit for a cooker, shower or immersion heater" as notifiable electrical work under Part P of the Building Regulations [10]. If your new cylinder needs a new immersion heater circuit, it should be done by an electrician registered with a competent person scheme, or notified to building control. The Planning Portal says most repairs, replacements and maintenance jobs outside special locations are not notifiable [10].

Gas work needs a competent, registered engineer. A cylinder swap on its own does not usually involve gas, but if the job touches the boiler or its gas supply, for example when the cylinder is replaced as part of a new boiler, the law says "No person shall carry out any work in relation to a gas fitting or gas storage vessel unless he is competent to do so" [11]. Gas Safe registration is how an engineer shows that competence, and you can check an engineer's registration before they start.

Safety first, not DIY. An unvented cylinder stores hot water under pressure, and its safety devices are what stop it overheating or over-pressurising. Do not attempt to fit, adjust or repair one yourself, and do not tamper with the valves or the discharge pipe.

Repair or replace?

Not every cylinder problem means a new cylinder. A fault with an immersion heater, a thermostat or a valve can often be fixed on its own, and a plumber should diagnose the fault before quoting for a full replacement. No dated source gives a price for these smaller repairs, so ask for a diagnosis charge and a repair quote first.

A leaking cylinder is different. If water is coming from the cylinder itself rather than a fitting, call a plumber straight away, and do not touch the valves or the discharge pipe. If you need help out of hours, our guide to emergency plumber costs in London sets out what call-outs cost. If the cylinder sits on a heating system that keeps losing pressure, our guide to why a boiler keeps losing pressure explains the common causes.

Planning a heat pump? Ask before you replace. The Boiler Upgrade Scheme is open to people in England and Wales [21]. It gives "£7,500 towards an air source heat pump" or "£7,500 towards a ground source heat pump", and lists heat pumps and biomass boilers as the eligible items; the Gov.uk page does not list hot water cylinders on their own [13]. If you are thinking about a heat pump in the next few years, ask the installer whether the cylinder you are buying now would suit it, so you do not risk paying for the job twice.

Temperature and safety settings

A stored hot water cylinder should be hot enough to control bacteria. The Health and Safety Executive's guidance for landlords includes "setting the temperature of the hot water cylinder (calorifier) to ensure water is stored at 60°C" as a control measure for legionella [12]. Ask your installer what temperature they have set the cylinder thermostat to, and where it is.

Servicing an unvented cylinder. Trade2Base says an unvented cylinder "must be serviced annually", checking the expansion vessel charge and relief valves [3], and Book A Builder puts an annual service at about £80 to £150 [4]. We could not confirm this from a manufacturer or an official source, so check the manual and warranty for the cylinder you choose; some warranties depend on a regular service.

Do plumbers charge VAT on cylinder replacement?

VAT depends on the trader. The standard rate of VAT is 20% [14], and a business must register for VAT once its taxable turnover for the last 12 months goes over £90,000 [15]. A sole trader below that threshold may not charge VAT, which is one reason two quotes for the same job can differ by 20 percent.

No VAT relief applies to a cylinder replacement as far as we can find. HMRC's VAT Notice 708/6 zero-rates the installation of certain energy-saving materials until 31 March 2027, but its list does not include hot water cylinders [16]. Insulation for water tanks and pipes is on the list, so if your quote includes separate insulation work, ask how it has been treated.

If you rent

If you rent your home in England, the cylinder is usually your landlord's responsibility. Section 11 of the Landlord and Tenant Act 1985 requires the landlord of a lease of under seven years, which covers most private tenancies, "to keep in repair and proper working order the installations in the dwelling-house for space heating and heating water" [20][22]. Tenancy law differs in Wales, Scotland and Northern Ireland, so check your own agreement. Report a failed or leaking cylinder to your landlord in writing, and keep a copy.

How to choose a plumber for a cylinder replacement

Check registration for the work being done. For an unvented cylinder, ask which competent person scheme covers the installer's unvented work [9]. For gas work, check Gas Safe registration. For a new immersion heater circuit, check the electrician's scheme [10]. TrustMark, the Government Endorsed Quality Scheme, advises: "Make sure the tradesperson is registered with TrustMark for the specific trade you need" [19].

Know your rights. Under the Consumer Rights Act 2015, "Every contract to supply a service is to be treated as including a term that the trader must perform the service with reasonable care and skill" [17]. If a cylinder is fitted badly, you can ask the trader to put it right.

Agree payment terms before work starts. Put any deposit and the payment stages in writing. Our guide to how much deposit to pay a tradesperson explains what is reasonable. For a wider checklist, see how to find a trusted London tradesperson.

Look after the system once it is in. If your cylinder is heated by the boiler and the radiators are slow or the water is dirty, a power flush may be worth discussing at the same visit. Some smart thermostats can also schedule hot water, so check whether yours can.

Find a plumber for your hot water cylinder

Loacally is a UK platform for finding local tradespeople, starting in London across all 33 boroughs. You can find a trusted local plumber near you, compare their profiles and book or request a visit directly. Get at least three written quotes, compare them line by line against the checklist above, and choose the one that lists everything.

Frequently asked questions

How much does it cost to replace a hot water cylinder?

A like-for-like replacement of a vented hot water system costs about £350 to £1,000 in labour and materials, excluding VAT and the tank, on Which?'s November 2025 survey of 25 Trusted Traders. A full unvented cylinder supply and fit typically costs £1,500 to £3,500, on a June 2026 trade guide. Which? says London prices are likely to be higher.

How much does an unvented cylinder cost to buy?

An unvented cylinder costs about £500 to £750 for 150 litres, £650 to £950 for 210 litres and £850 to £1,200 or more for 250 litres or larger, on a June 2026 trade guide. On 17 November 2026, one merchant listed a branded 210 litre model at £1,162.80 including VAT, and another listed a different brand at £1,801.95.

Does replacing a hot water cylinder need building regulations approval?

In England, hot water storage is controlled by the Building Regulations, and LABC says a unit holding more than 15 litres is notifiable; smaller units on an exempt electricity supply are not. A registered installer can self-certify the work through a competent person scheme. Otherwise, a Building Notice or full plans application to the council is needed.

Who can install an unvented hot water cylinder?

Gov.uk lists unvented hot water storage systems as a separate technical competence for competent person schemes, so ask the installer which scheme covers their unvented work and check their registration before they start. A registered installer can self-certify the job. If the work involves the boiler or gas supply, a Gas Safe registered engineer is needed.

Is it cheaper to replace a vented cylinder with another vented one?

Often, but the published prices do not compare like with like. Which? gives £350 to £1,000 for a vented swap, excluding the tank and VAT. Trade2Base gives £1,500 to £3,500 for a full unvented supply and fit, including the cylinder. Unvented jobs add safety equipment and certified installation, so ask each installer to price the cylinder and labour separately.

How long does it take to replace a hot water cylinder?

A like-for-like replacement of a vented hot water system takes about half a day to a full day, according to Which?'s November 2025 survey of Trusted Traders. Jobs that change the system type, move the cylinder or need new pipework take longer. Ask your installer how many days they have priced for and how long you will lack hot water.

Sources

  1. Which? - How much do plumbers cost? (row "Replace a standard hot-water tank"; survey of 25 Which? Trusted Traders, November 2025; prices exclude VAT) - https://www.which.co.uk/reviews/finding-a-tradesperson/article/how-much-do-plumbers-cost-awJxi6S98hqB - page date shown 1 May 2026, checked 17 November 2026.
  2. Which? - Boiler prices: how much does a new boiler cost? (cylinder figures when swapping a combi for a boiler with a hot water tank) - https://www.which.co.uk/reviews/boilers/article/buying-a-new-boiler/boiler-prices-how-much-does-a-new-boiler-cost-aK2dh2j3Cabo - page dated 17 September 2025, checked 17 November 2026.
  3. Trade2Base - Unvented cylinder costs UK (a software firm's pricing guide for tradespeople; method and VAT basis not stated; used for price context only) - https://www.trade2base.com/blog/unvented-cylinder-costs-uk - 14 June 2026, checked 17 November 2026.
  4. Book A Builder - UK water tank replacement cost 2026 (a trade directory and marketplace's guide, based on its stated hands-on experience; no survey method; used for price context only) - https://www.bookabuilderuk.com/blog/uk-water-tank-replacement-cost-2026 - published 13 June 2026, checked 17 November 2026.
  5. City Plumbing - Gledhill StainlessLite System Ready unvented indirect 210L hot water cylinder (PROIN210PPSR), listed price including VAT - https://www.cityplumbing.co.uk/p/gledhill-stainlesslite-system-ready-unvented-indirect-210l-hot-water-cylinder-proin210ppsr/p/262789 - no page date, price captured 17 November 2026.
  6. Heat and Plumb - Heatrae Sadia Megaflo Eco unvented indirect cylinder, 210 litre listed price (VAT labelled only on the default 125 litre price) - https://www.heatandplumb.com/acatalog/heatrae-sadia-megaflo-eco-unvented-indirect-cylinder - no page date, price captured 17 November 2026.
  7. legislation.gov.uk - The Building Regulations 2010, Schedule 1, Part G (requirement G3, hot water supply and systems) - https://www.legislation.gov.uk/uksi/2010/2214/schedule/1 - up to date to 16 November 2026, checked 17 November 2026.
  8. Local Authority Building Control (LABC) - Don't find yourself in hot water! - https://www.labc.co.uk/news/dont-find-yourself-in-hot-water - published 24 November 2022, checked 17 November 2026.
  9. Gov.uk - Competent person scheme: current schemes and how schemes are authorised - https://www.gov.uk/guidance/competent-person-scheme-current-schemes-and-how-schemes-are-authorised - last updated 17 September 2026, checked 17 November 2026.
  10. Planning Portal - Electrics: Building Regulations (Part P notifiable work) - https://www.planningportal.co.uk/permission/common-projects/electrics/building-regulations/ - no page date shown, checked 17 November 2026.
  11. legislation.gov.uk - The Gas Safety (Installation and Use) Regulations 1998, regulation 3 - https://www.legislation.gov.uk/uksi/1998/2451/regulation/3 - checked 17 November 2026.
  12. Health and Safety Executive - Legionnaires' disease: landlords' responsibilities - https://www.hse.gov.uk/legionnaires/legionella-landlords-responsibilities.htm - updated 30 September 2024, checked 17 November 2026.
  13. Gov.uk - Apply for the Boiler Upgrade Scheme: what you can get - https://www.gov.uk/apply-boiler-upgrade-scheme/what-you-can-get - no page date shown, checked 17 November 2026.
  14. Gov.uk - VAT rates - https://www.gov.uk/vat-rates - checked 17 November 2026.
  15. Gov.uk - Register for VAT - https://www.gov.uk/register-for-vat - checked 17 November 2026.
  16. HMRC, Gov.uk - VAT on energy-saving materials and heating equipment (VAT Notice 708/6) - https://www.gov.uk/guidance/vat-on-energy-saving-materials-and-heating-equipment-notice-7086 - last updated 31 January 2024, checked 17 November 2026.
  17. legislation.gov.uk - Consumer Rights Act 2015, section 49 - https://www.legislation.gov.uk/ukpga/2015/15/section/49 - checked 17 November 2026.
  18. Citizens Advice - Before you get building work done - https://www.citizensadvice.org.uk/consumer/getting-home-improvements-done/before-you-get-building-work-done/ - checked 17 November 2026.
  19. TrustMark - Government Endorsed Quality Scheme - https://www.trustmark.org.uk/ - checked 17 November 2026.
  20. legislation.gov.uk - Landlord and Tenant Act 1985, section 11 - https://www.legislation.gov.uk/ukpga/1985/70/section/11 - checked 17 November 2026.
  21. Gov.uk - Apply for the Boiler Upgrade Scheme (eligibility: England and Wales) - https://www.gov.uk/apply-boiler-upgrade-scheme - checked 17 November 2026.
  22. legislation.gov.uk - Landlord and Tenant Act 1985, section 13 (leases to which section 11 applies) - https://www.legislation.gov.uk/ukpga/1985/70/section/13 - checked 17 November 2026.
hot water cylinder replacement costunvented cylinder costvented cylinderhot water tank replacementbuilding regulationsplumbingcosts
Share

Need a plumber in London?

See who’s nearby, compare clear prices, and book a visit in minutes.